Re: SER1 Still begging...

[prev] [thread] [next] [Date index for 2004/07/13]

--Apple-Mail-1--284696525
Content-Transfer-Encoding: 7bit
Content-Type: text/plain;
	charset=US-ASCII;
	format=flowed

Nigel,

The bits showed up Saturday. Don't worry about the condition. With a 
little bit of buffing they look just like the ones I already had.

I'll get a check (cheque?) off to you to cover the postage.

Thanks again for your help.

Bill Lawrence

On Jun 29, 2004, at 6:39 AM, nigel.radestock@xxx.xx.xx wrote:

> Bill,
>
> They are on their way to you.
>
> Nigel
>
>
> On 29 Jun 2004, at 03:47, Bill Lawrence wrote:
>
>> Nigel,
>>
>> There is quite a bit of difference isn't there. I believe the shorter 
>> ones will be fine. I'm afraid the longer ones would bottom on the 
>> studs before they tighten.
>> They all look the same from the outside so anyone who notices if they 
>> are incorrect is getting much too intimate with my motor!!!
>>
>> Thanks again.
>>
>> Bill
>>
>> On Jun 28, 2004, at 5:38 AM, nigel.radestock@xxx.xx.xx wrote:
>>
>>> Bill,
>>>
>>> I have tried several times to email these pictures but they always 
>>> seem to get lost. I have placed the first one on my web site.
>>>
>>> http://www.zen27187.zen.co.uk/
>>>
>>> Nigel
>>>
>>>
>>>
>>>> Bill,
>>>>
>>>> I have removed the valve cover nuts and the exhaust clamp.
>>>> But there seems to be two different sorts holding down my valve 
>>>> cover (see pic IMG_0863.jpg) and another sort holding down the side 
>>>> tappet cover (see pic IMG_0864.jpg), the one on the left is the 
>>>> side plate nut the one on the right from the top cover. Even though 
>>>> they all have the same part number!
>>>>
>>>> Which ones would you like!
>>>>
>>>> Nigel
>>>>
>>>>  
--Apple-Mail-1--284696525
Content-Transfer-Encoding: 7bit
Content-Type: text/enriched;
	charset=US-ASCII

Nigel,


The bits showed up Saturday. Don't worry about the condition. With a
little bit of buffing they look just like the ones I already had.


I'll get a check (cheque?) off to you to cover the postage.


Thanks again for your help.


Bill Lawrence


On Jun 29, 2004, at 6:39 AM, nigel.radestock@xxx.xx.xx wrote:


<excerpt>Bill,


They are on their way to you.


Nigel



On 29 Jun 2004, at 03:47, Bill Lawrence wrote:


<excerpt>Nigel,


There is quite a bit of difference isn't there. I believe the shorter
ones will be fine. I'm afraid the longer ones would bottom on the
studs before they tighten. 

They all look the same from the outside so anyone who notices if they
are incorrect is getting much too intimate with my motor!!!


Thanks again.


Bill


On Jun 28, 2004, at 5:38 AM, nigel.radestock@xxx.xx.xx wrote:


<excerpt><bigger>Bill,


I have tried several times to email these pictures but they always
seem to get lost. I have placed the first one on my web site.


</bigger>http://www.zen27187.zen.co.uk/


Nigel




<excerpt><bigger>Bill,


I have removed the valve cover nuts and the exhaust clamp.

But there seems to be two different sorts holding down my valve cover
(see pic IMG_0863.jpg) and another sort holding down the side tappet
cover (see pic IMG_0864.jpg), the one on the left is the side plate
nut the one on the right from the top cover. Even though they all have
the same part number!


Which ones would you like!


Nigel


 </bigger></excerpt></excerpt></excerpt></excerpt>
--Apple-Mail-1--284696525--


To change subscription see www.landrover.net/series1/mail