Re: SER1 How to start an engine after 30 years?

[prev] [thread] [next] [Date index for 2004/12/30]

From: Wayne Perrin
Subject: Re: SER1 How to start an engine after 30 years?
Date: 13:48 on 30 Dec 2004
Ulrico,
Nick's advice is sound. I did the same thing with my 80" when I ran it. 
  another obvious area to check is the intake and exhaust areas for 
things like a mouse nest or an insect colony.  Any unused cavity 
becomes a home for little creatures.  An intermediate step is to put 
plugs on the leads and crank the engine  with them grounded to the 
outside of the motor. You want to be sure you have spark to each one 
before you torque them in place.
Wayne
On Thursday, December 30, 2004, at 02:41  AM, Ulrico Becker wrote:

> Hello everybody!
>
> I hope you all had a merry Xmas and thoroughly enjoyed feasting and
> partying, laying on the beach, shivering in the cold, praying, working,
> snoozing or whatever else is usual in your countries!
>
> My 80" has found its way to my garage and I will start to work on it. 
> A big
> issue is the question of what to do to start an engine that has stood 
> for
> decades?
>
> I have never done anything like that and am a bit at a loss as to what 
> to
> do.
>
> My instinct tells me to turn the crank by hand (already done, it 
> turns),
> then check oil. Following this put in a battery and jury rig the 
> starter and
> see what happens, but with the plugs out, just to get the oil system 
> up and
> running.
>
> Next step would be to see whether it fires up. I would not put in 
> coolant as
> I only want to give it a short run.
>
> What are your opinions? What else should I do? Or should I do it
> differently? Would you possibly skip this and dismantle the engine 
> straight
> away?
>
> cheers, Ulrico
>
>
> To change subscription see www.landrover.net/series1/mail
>


To change subscription see www.landrover.net/series1/mail

(message missing)

SER1 Welsh/frost-plugs
21:00 on 06 Sep 2004

Re: SER1 Welsh/frost-plugs
GRAHAM WOOD 21:22 on 06 Sep 2004

Re: SER1 Welsh/frost-plugs
MARTIN 20:14 on 07 Sep 2004

Re: SER1 Welsh/frost-plugs
Ian Stuart 08:25 on 09 Sep 2004

SER1 old flasher switch with hazardrelay ?
Brett Pritt 16:07 on 09 Dec 2004

Re: SER1 old flasher switch with hazardrelay ?
Bob Phillips 17:56 on 09 Dec 2004

RE: SER1 old flasher switch with hazardrelay ?
Peter Stone 20:39 on 09 Dec 2004

RE: SER1 old flasher switch with hazardrelay ?
Brett Pritt 06:25 on 10 Dec 2004

Re: SER1 old flasher switch with hazardrelay ?
Mark STRANGWAYS 17:04 on 12 Dec 2004

SER1 pedalshaft measure for lathe ?
Brett Pritt 14:22 on 05 Jan 2005

AW: SER1 old flasher switch with hazardrelay ?
Ulrico Becker 10:10 on 11 Dec 2004

Re: SER1 old flasher switch with hazardrelay ?
Diana Alan 10:38 on 11 Dec 2004

SER1 fuel problem?
Brett Pritt 11:50 on 18 May 2005

Re: SER1 fuel problem?
Andreas Demosthenous 11:56 on 18 May 2005

Re: SER1 fuel problem?
Brett Pritt 13:11 on 18 May 2005

RE: SER1 fuel problem?
Tom Tollefson 12:42 on 18 May 2005

Re: SER1 fuel problem?
Anthony Brain 21:38 on 18 May 2005

Re: SER1 old flasher switch with hazardrelay ?
Valentin Nemeth 12:59 on 10 Dec 2004

RE: SER1 old flasher switch with hazardrelay ?
Tom Tollefson 14:52 on 10 Dec 2004

SER1 Where is Santa?
Brett Pritt 20:26 on 23 Dec 2004

SER1 round Smith heater restauration
Brett Pritt 10:56 on 27 Dec 2004

Re: SER1 round Smith heater restauration
Allan Harding 03:41 on 29 Dec 2004

SER1 How to start an engine after 30 years?
Ulrico Becker 07:41 on 30 Dec 2004

RE: SER1 How to start an engine after 30 years?
Nick Condon 08:59 on 30 Dec 2004

Re: SER1 How to start an engine after 30 years?
Allan Harding 22:05 on 30 Dec 2004

AW: SER1 How to start an engine after 30 years?
Ulrico Becker 09:35 on 09 Jan 2005

AW: SER1 How to start an engine after 30 years?
Ulrico Becker 09:35 on 09 Jan 2005

Re: SER1 How to start an engine after 30 years?
Wayne Perrin 13:48 on 30 Dec 2004

AW: SER1 How to start an engine after 30 years?
Ulrico Becker 09:35 on 09 Jan 2005

SER1 Truck cab for SI 80"
Ulrico Becker 09:35 on 09 Jan 2005

AW: SER1 old flasher switch with hazardrelay ?
Ulrico Becker 07:52 on 14 Dec 2004

RE: SER1 How to start an engine after 30 years?
Nick Condon 13:14 on 01 Jan 2005

Re: SER1 fuel problem?
Tom Wykes 13:25 on 18 May 2005

Generated at 16:59 on 28 Jul 2005 by mariachi v0.52