Re: SER1 I forgot: Windsreen motors adjusting ?

[prev] [thread] [next] [Date index for 2005/03/13]

--Apple-Mail-10--777961865
Content-Transfer-Encoding: quoted-printable
Content-Type: text/plain;
	charset=WINDOWS-1252;
	format=flowed

Uli,

Check the end of the wiper shaft inside the motor to make sure the=20
small pin that engages the gear mechanism has not broken off.  If it=20
has, the shaft will partially "freewheel" and not make the full sweep. =20=

  It needs to protrude on both sides of the shaft for the motor to=20
rotate it in both directions.

Wayne Perrin
On Saturday, March 12, 2005, at 07:01 PM, Diana Alan wrote:

> G'Tag Uli
> =A0
> You need to change the wheel inside the motor however I thought the=20
> standard sweep area was 110 deg=A0(with some after market replacements=20=

> going to 130 deg for the MG TC's etc=A0).=A0
> =A0
> If you are only getting 90 deg then there is wear in the components.=A0=20=

> If you have access to a small lathe you=A0could solve the problem by =
re=20
> bushing the shafts/crank etc.=A0=A0Also if you are very handy you =
could=20
> reposition the post further out on the gear wheel to give you=A0a=20
> increased range of travel.=A0 But be careful not to go too far!!!!!!=A0
> =A0
> Cheers
> Diana=A0=A0
> ----- Original Message -----
> From: Brett Pritt
> To: series1@xxxxxxxxx.xxx
> Sent: Sunday, March 13, 2005 8:18 AM
> Subject: SER1 I forgot: Windsreen motors adjusting ?
>
> Is it possible to adjust the travelling arm of the motor. Mine weeps=20=

> only a 90=B0 area. Is it possible to changed the endpoints, maybe 120=B0=
=20
> angle or a bit more? And where/how to adjust?
>
> Thanks
>
> Uli
>

>
<image.tiff>
>
> Egal wo Sie sind =96 MSN Hotmail ist bei Ihnen. Hier klicken! Jetzt=20
> kostenlos anmelden und =FCberall erreichbar sein.=

--Apple-Mail-10--777961865
Content-Transfer-Encoding: quoted-printable
Content-Type: text/enriched;
	charset=WINDOWS-1252

Uli,


Check the end of the wiper shaft inside the motor to make sure the
small pin that engages the gear mechanism has not broken off.  If it
has, the shaft will partially "freewheel" and not make the full sweep. =20=

It needs to protrude on both sides of the shaft for the motor to
rotate it in both directions.


Wayne Perrin

On Saturday, March 12, 2005, at 07:01 PM, Diana Alan wrote:


<excerpt><fontfamily><param>Arial</param><smaller>G'Tag =
Uli</smaller></fontfamily>

=A0

<fontfamily><param>Arial</param><smaller>You need to change the wheel
inside the motor however I thought the standard sweep area was 110
deg=A0(with some after market replacements going to 130 deg for the MG
TC's etc=A0).=A0</smaller></fontfamily>

=A0

<fontfamily><param>Arial</param><smaller>If you are only getting 90
deg then there is wear in the components.=A0 If you have access to a
small lathe you=A0could solve the problem by re bushing the shafts/crank
etc.=A0=A0Also if you are very handy you could reposition the post =
further
out on the gear wheel to give you=A0a increased range of travel.=A0
<bold>But be careful not to go too =
far!!!!!!=A0</bold></smaller></fontfamily>

=A0

<fontfamily><param>Arial</param><smaller>Cheers</smaller></fontfamily>

<fontfamily><param>Arial</param><smaller>Diana=A0=A0</smaller></fontfamily=
>

----- Original Message -----

<bold>From:</bold>
<underline><color><param>1999,1999,FFFF</param>Brett =
Pritt</color></underline>

<bold>To:</bold>
=
<underline><color><param>1999,1999,FFFF</param>series1@xxxxxxxxx.xxx</colo=
r></underline>

<bold>Sent:</bold> Sunday, March 13, 2005 8:18 AM

<bold>Subject:</bold> SER1 I forgot: Windsreen motors adjusting ?


Is it possible to adjust the travelling arm of the motor. Mine weeps
only a 90=B0 area. Is it possible to changed the endpoints, maybe 120=B0
angle or a bit more? And where/how to adjust?


Thanks


Uli


</excerpt>=20

<excerpt>

</excerpt><<image.tiff>

<excerpt>

Egal wo Sie sind =96 MSN Hotmail ist bei Ihnen.
<underline><color><param>1999,1999,FFFF</param>Hier
klicken!</color></underline> Jetzt kostenlos anmelden und =FCberall
erreichbar sein.</excerpt>=

--Apple-Mail-10--777961865--


To change subscription see www.landrover.net/series1/mail